Re: No USB power when D34010WYK is in Hibernate
Lmbg, I am sorry to hear you are having problems with your system. However, since you already performed all troubleshooting we suggested, I would recommend you to contact our warranty department and...
View ArticleRe: HD5000 / Windows 7-64 DP1.2 MST Hub Multi-monitor Issue
Hi Alan, Thanks for the reply. I'm not sure this is a case of exceeding maximum bandwidth. (3 x 1080p is far less bandwidth compared to DisplayPort 1.2 maximum). The monitor actually shows up on the...
View ArticleRe: Problem with HDMI audio using intel hd 4600 graphics
Thank you all for the feedback. I am really sorry to hear you are still having these problems but I will immediately report everything to the development team. At this point the latest driver has been...
View ArticleRe: Problem with HDMI audio using intel hd 4600 graphics
Feel free to send me a 4th gen chip to replace my current 2nd gen - here's my DxDiag.My setup is NVidia GPU powering 27" ASUS monitor Intel 2500K HD3000 powering 19" Samsung monitor and 46" Panasonic...
View ArticleRe: Problem with HDMI audio using intel hd 4600 graphics
I think I can guess the answer to this....A quick check of the release notes show that this update does not mention having fixed the problem with rebooting the computer to get the HDMI audio back....
View ArticleRe: ETA on full-speed UART?
Hi TyberiusPlease take a look at this post related to Software Serial: https://communities.intel.com/thread/47898 as you noticed the Software serial is currently not supported, you can check the list...
View ArticleSketch transfer incomplete need assistance
Hello all, So I've successfully updated the firmware (0.7.5) and booting from an SD with the Linux image (LINUX_IMAGE_FOR_SD_Intel_Galileo_v0.7.5.7z). The issue is that now I am not able to upload...
View ArticleRe: Intel AC7260 problems
I've got the latest drivers on windows 8.1 for the desktop version of this card, and I'm getting bad latency spikes every ~1min or so. Latency is usually about 5ms but shoots up to 200ms for a few...
View ArticleRe: D34010WYK does neither boot from USB 3.0 nor boots with plugged USB 3.0...
Hi Sylvia, if I remember correctly, it came with version 22 installed. When I noticed my USB drive wasn't recognised in both the bios and boot menu I upgraded to the latest version (24).When that...
View ArticleRe: Memory Issue for DZ87KLT-75K
Thanks for the information. I have been testing the same board with 16GB of RAM memory (F3-1866C10D-16GSR) I have not encounter problems running that amount of memory. In regards the PCI issue, the...
View ArticleRe: Display control issue Win 8.1 & HD 4000!!
Hi KevinThanks again for your help.I have now installed the new driver and have found how to change the display settings as I have been able to previously. So that's me sorted!!
View ArticleRe: Windows *7/8/8.1 GFX Driver Version 3412
I have a Samsung NP740U3E with a HD4000 graphics adapter (only). I have been getting the infamous Code 43 since I (stupidly) updated to Windows 8.1. I installed the 3412 driver with high hopes, but...
View ArticleRe: Operating NUC DN2820FYH on battery - power supply ratings
G.Threepwood, The DN2820FYH nominal requirement is 12V +/- 5%. More-typically, anything from 11V-13V should be ok. You will get a stop warning if the voltage detected is over 13V... ...S
View ArticleRe: Windows *7/8/8.1 GFX Driver Version 3412
@nic- The memory leak that several of us described to you in the later pages of the 3345 driver still exist in this version of the driver as well.
View ArticleRe: D34010WYK - processor input voltage
Intel(R) Desktop Utilities is not supported on the NUC products. You use it at your own risk. It has been found to work on the D34010WYB and D54250WYB boards but not on any others (either install will...
View ArticleRe: Windows 7 UX32VD WiDi doesn't connect
Latest Intel® WiDi version for Windows* 7 is 4.2.24. It should work at this point, unless… the TV adapter is not working properly? How is the computer connecting to your AP, is it 2.4 or 5 GHz?...
View ArticleRe: DN2820FYKH - Win7 support coming?
Even after following all the suggestions listed here (and elsewhere) I still can't get my DN2820 to work after installing Win7. Everything seems OK at 1st - the PC boots from the USB flash drive with...
View ArticleRe: GPIO pin goes high on reboot of Galileo board?
I'm having the same problem and a 10K pulldown did not help. Please let us know what you find out! Thanks. I may decide to add not gates and go to negative logic but that will be tough to fit on my...
View ArticleRe: Inconsistent update notices for HD4600
Yes, you should be able to update to this driver. Keep in mind if the system has an OEM (Clevo) specific driver with customization, you will loose them when install the generic driver from Intel...
View Article